Gears & Girders Editorial Team ยท Last reviewed November 20, 2026 ยท How we research

Short answer

A gear ratio compares the teeth on two meshing gears, and it tells you how speed and torque swap places. When a small gear drives a gear with three times as many teeth, the big gear turns three times slower but pushes with about three times the torque. The gears do not create energy: power going in equals power coming out, minus a small loss to friction.

12 : 1The reduction between the minute hand and the hour hand in a mechanical clock
98 to 99.5%Typical efficiency of a spur gear pair, according to gear maker KHK
30 to 90%Efficiency range KHK gives for worm gears, which slide more than they roll

What a gear ratio actually is

Put two gears together so their teeth interlock. The one connected to the motor, the crank or your hand is the driver. The one it pushes is the driven gear. Every time one tooth of the driver passes the meshing point, exactly one tooth of the driven gear passes too. Teeth cannot skip, so the gears always move the same number of teeth past each other.

That simple rule gives you the gear ratio. If the driver has 12 teeth and the driven gear has 36, one full turn of the driver moves 12 teeth along, which is only a third of a turn of the big gear. Gear makers write this as:

gear ratio = teeth on driven gear รท teeth on driver = 36 รท 12 = 3 (written 3 : 1)
output speed = input speed รท gear ratio

Japanese gear maker KHK uses the same definition in its technical guide, with a worked example: a 20 tooth gear turning at 400 rpm drives an 80 tooth gear, the ratio is 80 รท 20 = 4, and the big gear turns at 400 รท 4 = 100 rpm.

Fig. 1 ยท A 3 : 1 spur gear pair

1 2 3 4
1Driver, 12 teeth. Turns fast with low torque.
2Driven gear, 36 teeth. Turns 3 times slower with about 3 times the torque.
3Mesh point. Both gears move the same number of teeth past here.
4Direction. Two meshing outside gears always turn opposite ways.

A ratio bigger than 1 is a reduction: the output is slower and stronger. A ratio smaller than 1 is an increase (often called overdrive in cars): the output is faster and weaker. A ratio of exactly 1 just passes the motion along, sometimes to change direction or to move it to another shaft.

Watch the notation. Some sources write the same pair as 3 : 1, others as 1 : 3, and bike and car manuals have their own habits. Always check which gear is the driver before comparing numbers. On this page the first number belongs to the driven gear, as in KHK’s guide.

Why speed goes down when torque goes up

The trade comes from one physics rule. For anything that spins, power equals torque multiplied by angular speed. A gear pair cannot add power, it can only pass it along, so if the speed drops by three, the torque has to rise by three to keep the product the same.

power = torque ร— angular speed
P (watts) = T (Nยทm) ร— rpm ร— 2ฯ€ รท 60
output torque โ‰ˆ input torque ร— gear ratio ร— efficiency

Here is a worked example with round numbers, the kind you would do on the back of an envelope for a small motor and gearbox.

  1. Start with the motor. It turns at 1,500 rpm and gives 2.0 Nยทm (1.48 lbยทft). Power in = 2.0 ร— 1,500 ร— 2ฯ€ รท 60 โ‰ˆ 314 W.
  2. Add a 3 : 1 reduction. A 12 tooth gear drives a 36 tooth gear. Output speed = 1,500 รท 3 = 500 rpm.
  3. Multiply the torque. With perfect gears the output would be 2.0 ร— 3 = 6.0 Nยทm. A spur pair at about 98% efficiency gives roughly 5.9 Nยทm (4.3 lbยทft).
  4. Check the power. 5.9 Nยทm at 500 rpm โ‰ˆ 308 W. About 6 W turned into heat at the teeth, which is why gearboxes get warm.

This is exactly how a long wrench works, just in a circle. The teeth of the big gear sit further from its centre, so the same tooth force acting on a bigger radius makes more torque. Our torque lab on the home page lets you play with that lever effect on its own.

Stacking gears: idlers and compound trains

One pair of gears can only give a limited ratio before the big gear becomes huge. Engineers get around this in two ways.

Idler gears change direction, not the ratio

Put a third gear between the driver and the driven gear and the output turns the same way as the input. The idler’s own tooth count cancels out: the driver moves its teeth, the idler passes exactly the same number of teeth along, and the driven gear receives them. KHK’s guide states it plainly: an idler has no effect on the speed ratio.

Compound gears multiply ratios

Now fix two gears of different sizes on the same shaft. The first one is driven by the input, and the second one, turning at the same speed, drives the next gear along. The ratios of each stage multiply. A clock’s motion work, the little train that turns the hour hand from the minute hand, is a perfect example. A teaching example from Princeton uses gears with 15, 45, 12 and 48 teeth:

stage 1: 45 รท 15 = 3
stage 2: 48 รท 12 = 4
total = 3 ร— 4 = 12 โ†’ the hour hand turns once for every 12 turns of the minute hand

Getting 12 : 1 from a single pair would need a gear 12 times wider than the pinion. Splitting it into two stages keeps the whole mechanism small enough to hide behind a clock dial.

Try it: build a gear train

Set the teeth on each gear, choose the motor speed and torque, and watch the train turn. Add a second stage to see ratios multiply. The animation runs in slow motion, but every gear keeps its true speed relative to the others.

Gear train benchInteractive ยท Fig. 2

Gear 1, driverGear 2Gear 3, fixed to gear 2Gear 4, output

Overall ratio3.00 : 1Reduction
Output speed500 rpmOpposite direction
Output torque5.88 Nยทm4.34 lbยทft
Power in / out314 / 308 W6 W lost as heat

Gear ratios in real machines

The same arithmetic shows up everywhere once you start looking. These examples use tooth counts published in the sources listed at the end of this guide.

WhereTeethRatioWhat it does
KHK catalogue example20 drives 804 : 1Turns 400 rpm into 100 rpm with about four times the torque
Clock motion work15 / 45, then 12 / 4812 : 1Turns the hour hand once for every 12 turns of the minute hand
Planetary set, ring fixedSun 16, ring 484 : 1Sun in, carrier out: ratio = ring รท sun + 1, all in one compact ring
Bicycle, low gear48 chainring, 34 sprocket1 : 1.41Wheel turns 1.41 times per crank turn: easy climbing
Bicycle, top gear48 chainring, 11 sprocket1 : 4.36Wheel turns 4.36 times per crank turn: fast on the flat

Why your bike gears feel the way they do

A bicycle is the gear ratio you can feel in your legs. Your legs are slow and strong compared with the speed a wheel needs, so a bike almost always increases speed: the chainring is bigger than the rear sprocket. Shifting to a bigger sprocket at the back lowers that increase, so each pedal stroke moves you less far but feels lighter. That is the speed and torque trade again, with you as the motor.

Cyclists often quote gears in gear inches: wheel diameter ร— chainring teeth รท sprocket teeth. With a 26 inch wheel and a 48 tooth chainring, an 11 to 34 tooth cassette runs from about 37 gear inches to about 113. The late bike mechanic Sheldon Brown proposed a refinement called gain ratio, which also takes crank length into account, so it compares how far the bike moves with how far your pedal moves.

What the simple formula leaves out

The tooth count rule is exact for speed. Torque and long life depend on a few more things that designers have to get right.

Friction

Spur, helical and bevel gears mostly roll against each other, so KHK lists spur and helical pairs at 98 to 99.5% efficiency and bevel pairs at 98 to 99%. Worm gears slide a lot more, and KHK gives them 30 to 90%. That lost power is why a worm drive needs a bigger motor for the same output torque.

Hunting teeth

If the two tooth counts share a factor, the same teeth keep meeting the same gaps. A hunting tooth ratio, where the counts have no common factor, lets every tooth meet every gap, spreading wear evenly. That is why real gear pairs often have tooth counts like 11 and 31.

Matching teeth

Two gears can only mesh if their teeth are the same size and shape. In metric gears that size is called the module, and both gears in a pair must share it. You cannot pair any two gears just because the ratio looks right on paper.

Frequently asked questions

Is a higher gear ratio better?

Neither is better on its own. A high reduction ratio gives strong, slow output, which suits a winch or a car pulling away from a stop. A low ratio or an overdrive gives fast, weaker output, which suits cruising. Gearboxes exist so a machine can switch between them.

Do gears change the power of a motor?

No. Gears trade speed for torque, but the power that comes out is always the power that went in minus friction losses. A gearbox can never make a 300 W motor deliver more than 300 W.

How do I calculate the ratio of a gear train with several stages?

Work out the ratio of each meshing pair (driven teeth รท driver teeth) and multiply them together. Idler gears that sit alone on their shafts drop out of the calculation, because they only pass teeth along.

Why do the two gears turn in opposite directions?

Two external gears touch at a single point and their teeth move the same way at that point, so the gears must spin opposite ways. Add an idler, or use an internal (ring) gear, and the output turns the same way as the input.

Can gears make something spin faster?

Yes. Let the big gear drive the small one and the output speeds up, while the torque drops by the same factor. Bicycles, wind turbine gearboxes and the overdrive gears in a car all use this.

Why do some gears have odd tooth counts like 31 or 47?

Often it is deliberate. Choosing tooth counts with no common factor gives a hunting tooth ratio, so wear is shared across every tooth instead of the same pairs meeting on every turn.

The bottom line

Count the teeth, divide driven by driver, and you know how much a pair of gears slows the output and how much it multiplies the torque. Stack stages to multiply ratios, use an idler to flip the direction, and remember that friction takes a small cut along the way. Every gearbox, from a wristwatch to a wind turbine, is built on that one trade.

Sources

  1. KHK Gears, Gear Technical Reference (gear types, efficiency ranges, speed ratio of gear trains and idlers).
  2. KHK Gears, The ABC’s of Gears, Basic Guide B (20 to 80 tooth example, planetary gear speed ratio).
  3. OpenStax, University Physics Volume 1, 10.8 Work and Power for Rotational Motion (power equals torque times angular velocity).
  4. Princeton University, Connecting from the mechanism to the face (15, 45, 12 and 48 tooth motion work giving 12 : 1).
  5. Horopedia, Motion work (hour wheel turning 12 times slower than the cannon pinion).
  6. Wikipedia, Gear inches (26 inch wheel, 48 tooth chainring, 11 to 34 cassette example).
  7. Sheldon Brown, Gain Ratios: A New Way to Designate Bicycle Gears.
  8. Hermann J. Stadtfeld, The Hunting Tooth and its Effect on Break-In, Gear Technology (hunting tooth ratios and wear).

Spotted an error or have a question about this guide? Tell us and we will check it and update the page.

Keep exploring


Leave a Reply

Your email address will not be published. Required fields are marked *